Discover the power of PPKTP
Take your experiment to the next level. PPKTP crystals that generate entangled photon pairs — stock or custom-engineered, poled across the full transparency window, and shipped worldwide with an individual test report for every crystal.
What we make
Photon‑pair generation, frequency conversion, temperature control and single‑photon detection for quantum optics — engineered as one system, sold as components.
PPKTP Crystal
Entangled‑photon and frequency‑conversion crystals, stock or custom‑poled, individually tested.
Waveguide
Type‑0 and Type‑2 designs, bare chip or fiber‑coupled, tailored to your wavelength.
SPUD Photon Detector
Single‑photon upconversion detection at 1550 nm, room‑temperature, no cryostat.
Crystal Oven
Peltier‑driven temperature control engineered for every crystal size.
Waveguide
Unlock maximum efficiency with our advanced waveguide technology — Type‑0 and Type‑2 designs, bare chip or fully integrated fiber‑coupled modules, tailored to your wavelength and coupling scheme.

SPUD Photon Detector
Single Photon Upconversion Detector — upconverts telecom‑band photons to a wavelength its silicon SPAD detects efficiently. 1550 nm, room temperature, no cryostat, low afterpulsing.

Crystal Oven
A temperature control device engineered for every crystal size, driven by a built‑in Peltier element that holds the setpoint your phase‑matching depends on, run after run.

Phase-matching calculator
Calculate the poling period Λ, the signal and idler or generated wavelengths and how they tune with temperature, plus the temperature and spectral acceptance bandwidths (FWHM) for PPKTP, live in your browser and running the same model our engineers use.
Output
SLF Quantum designs and manufactures nonlinear optical components for quantum optics and photonics research, from our facility in Stockholm, Sweden. Our crystals, waveguides, detectors and ovens reach laboratories in 30+ countries across six continents.
Every PPKTP crystal ships with its own individual test report — because in quantum optics, the spec sheet is part of the experiment.
Request a quotation
Use the calculator to size your crystal, or send us your parameters directly — we'll turn it around with a quotation and, where relevant, a custom poling design.
PPKTP Crystals
Higher conversion efficiency from access to the highest nonlinear coefficient, with no spatial walk‑off. Periodic poling phase‑matches across the crystal's entire transparency region — stock and custom‑engineered.
Quasi-phase-matching in a periodically poled crystal: each flipped domain resets the phase, so the generated light keeps growing along the whole crystal. Pick a process to see how the wavelengths and the momentum balance change.
Specifications
| Transparency window | 0.4 – 3 µm (z‑pol, Type 0) · 0.4 – 4 µm (y‑pol, Type II) |
| Nonlinear coefficient | d₃₃ = 16.9 pm/V |
| Crystal length | up to 30 mm |
| Optical aperture | up to 4 × 4 mm² |
| Coatings | AR / HR optional |
| Poling | periodic & aperiodic |
Properties
Type‑II quasi‑phase‑matching gives orthogonally polarized signal and idler for polarization‑entangled sources — with zero spatial walk‑off, since every beam travels along a principal crystal axis.
Transparent from 0.4 to 3 µm for z‑polarized light (Type 0) and out to 4 µm for y‑polarized light (Type II) — covering 405 nm pumps, 810 nm photon pairs and the 1550 nm telecom band in one material.
Type‑0 quasi‑phase‑matching, with all waves polarized along z, puts KTP's largest coefficient to work — d₃₃ = 16.9 pm/V, which birefringent phase‑matching can't access.
Periodic poling phase‑matches almost any process across the transparency window — the period is designed around your wavelengths, not the other way around.
Stable under sustained high‑power operation, for long measurement runs and demanding sources alike.
Up to 4 × 4 mm² — larger than any other PPKTP supplier offers as standard, for bigger beams and looser alignment tolerances.
A test report for every crystal
Every PPKTP crystal is measured individually before it ships. The crystal is held at temperature in its mount, the pump is tuned across the band in fine steps, and the generated power is recorded at each step. That scan is the test report that follows the crystal: the sinc² curve is the theory, the points are the measurement.
Information we need
The more of this you can give us up front, the faster we can turn a quotation around.
- Target wavelength(s)Pump and signal/idler wavelengths for your process — or just the process, if you're not sure yet.
- ProcessSPDC, SHG, SFG, DFG or BWOPO — which conversion you're driving.
- Crystal dimensionsLength and aperture, or let us size it from your beam and power.
- CoatingsAR, HR, or uncoated — tell us which surfaces need it.
- Temperature setpointYour target operating temperature, if you already have one in mind.
- Quantity & timelineHow many crystals, and when you need them by.
Custom crystals
Tell us your wavelengths, bandwidth, temperature setpoint and polarization — we'll design the poling and quote the crystal.
Waveguides
Unlock maximum efficiency with our advanced waveguide technology, offered as bare chips or in fully integrated fiber‑coupled modules — configured to your process and coupling scheme.
Chip, fiber and mount
The waveguide chip, housing and clamp — with the PM fiber pigtails that couple light in and out, exactly as they sit in a finished module.
Chip, housing and pigtails, modeled to the exact tolerances we build to.
Configuration
Each waveguide starts from the process you need to drive and the wavelengths you work at. We set the poling period and phase‑matching type around them, then deliver it in one of three coupling schemes: a bare chip, fiber in with the converted light out in free space, or fiber in and fiber out.
Guiding light in a waveguide keeps intensity high along the entire interaction length, not just at a focus — for higher conversion efficiency from the same pump power.
Type‑0, with all fields co‑polarized, for the highest conversion efficiency; Type‑2 for orthogonally polarized outputs, as in polarization‑entangled pair sources.
A bare chip to integrate into your own assembly, fiber in with the converted light out in free space, or fiber in and fiber out as a fully packaged, pigtailed module ready to mount on your optical table.
Packaged and ready to use
The same waveguide can be delivered as a bare chip or built into a fiber‑pigtailed module: PM fiber in and out on FC/APC connectors, an integrated TEC and thermistor, and a single‑bolt mounting tab. There is no free‑space alignment to do. Wavelengths, poling period and phase‑matching type are set for your application.
Specifications
Typical values for the fiber‑coupled module. Wavelengths, poling period and phase‑matching type are set per order, and each module ships with its measured performance data.
| Nonlinear material | Periodically poled KTP |
| Phase matching | Type‑0 or Type‑2, quasi‑phase‑matched |
| Processes | SHG, SFG, DFG, SPDC |
| Waveguide length | up to 30 mm |
| Coupling | bare chip · fiber in, free‑space out · fiber in, fiber out |
| Input / output fiber | PM, chosen for your wavelengths |
| Connectors | FC/APC |
| Fiber length | 1 m on each side |
| Dimensions (L × W × H) | 64 × 24 × 19 mm |
| Mounting | single‑bolt mounting tab |
| Temperature control | integrated TEC, max 2 A / 4 V |
| Temperature sensor | NTC thermistor, 10 kΩ at 25 °C (B₂₅⁄₈₅ = 3434 K) |
| Electrical connection | 4 cables: TEC +, TEC −, NTC |
| Operating environment | 15–30 °C ambient, 0–85 %RH |
| Supplied with | measured performance data |
Where waveguides are used
Compact, fiber‑coupled conversion stages for entangled‑photon distribution and frequency conversion in fiber‑optic quantum links.
SPDC and SFG in a package small enough to sit directly on a transmitter board, not just an optical table.
Embed a conversion stage inside a larger instrument, with bare‑chip or pigtailed options to match your assembly.
Information we need
The more of this you can give us up front, the faster we can turn a quotation around.
- Process & wavelengthsSFG, SHG, SPDC or DFG, and the wavelengths involved.
- Type & polarizationType‑0 or Type‑2, depending on your beam geometry.
- CouplingBare chip, fiber in with free‑space output, or fiber in and fiber out — and connector/fiber type, if pigtailed.
- Quantity & timelineHow many units, and when you need them by.
Chip or module
Tell us your target wavelength, process and coupling scheme — wavelengths are tailored to your requirements.
SPUD — Single Photon Upconversion Detector
Upconverts telecom‑band photons by sum‑frequency generation to a wavelength its silicon single‑photon avalanche diode (SPAD) detects efficiently — single‑photon sensitivity at 1550 nm, at room temperature, with no cryostat.
A 1550 nm photon and the CW pump laser travel the same fiber into the PPKTP waveguide. Sum-frequency generation moves the photon into the visible, the filter dumps the pump, and the silicon SPAD counts what is left — one click per photon.
Specifications
| Detection wavelength | 1550 nm |
| Detection bandwidth | 0.6 nm (FWHM) |
| Timing jitter | 300 ps |
| Dead time | < 25 ns |
| Input | PM fiber |
| Output | SMA, TTL signal |
| Setup | Plug and play |
| Detection efficiency — current | 10% |
| Detection efficiency — target | 25% |
| Dark count rate — current | 30 kHz |
| Dark count rate — target | 10 kHz |
Where the SPUD is used
Upconversion detection of 1550 nm fiber‑network photons with a silicon SPAD — low dark counts, reduced afterpulsing, no cryogenic cooling.
Entangled photon pairs at telecom wavelengths, heralded single‑photon sources, photon statistics and correlation measurements.
Eye‑safe 1550 nm operation for long‑range detection, topographic mapping, and defense & aerospace applications.
No cryostat, no closed‑cycle cooler — fewer failure points and a smaller footprint on your optical table.
Dead time below 25 ns — shorter than that of typical superconducting nanowire single‑photon detectors (SNSPDs), for higher maximum count rates.
High long‑term stability and low afterpulsing, so your count statistics stay clean.
Information we need
The more of this you can give us up front, the faster we can turn a quotation around.
- Signal wavelength1550 nm by default — tell us if you need tuning around that.
- Expected count rateHelps us confirm dead‑time and dark‑count fit for your source.
- Fiber & connectorPM, SM or free‑space input, and your connector type.
- Triggering & timingGated or free‑running, and your timing reference, if any.
- Quantity & timelineHow many units, and when you need them by.
Detection for your source
Tell us your wavelength and count rate and we'll confirm fit.
Crystal Oven
A temperature control device engineered for every crystal size, driven by a built‑in Peltier element that holds the setpoint your phase‑matching depends on.
Housing, bracket and clamp
Housing, bracket and crystal clamp — sized around the PPKTP block it holds, so nothing shifts once you've found your phase‑matching temperature.
Temperature stability
A real run: the setpoint stepped between 25 and 75 °C, the Peltier element driving the crystal to each one and keeping it there.
Sized for our full PPKTP range, from short stock pieces to 30 mm custom cuts.
A built‑in Peltier element heats and cools to hold the temperature your phase‑matching condition depends on, run after run.
Set anywhere from 20 to 90 °C — enough range to reach the phase‑matching temperature your design calls for, and to fine‑tune your wavelengths in operation.
Mount outline
50 mm tall, 39 mm wide and 24 mm deep, with an M4×0.7 thread in the base for a standard post. The crystal aperture sits 37.7 mm above the mounting face, and the body fits a 30 mm cage.
Specifications
| Temperature range | 20 – 90 °C |
| Temperature stability | ± 0.1 °C |
| Heating and cooling | Peltier element |
| Temperature sensor | NTC |
| Crystal size | up to 30 mm long, 8 mm wide, 4 mm thick |
| Dimensions (W × D × H) | 39 × 24 × 50 mm |
| Mounting | M4×0.7 thread, post or cage mount |
| Maximum current / voltage | 1.9 A / 9.1 V |
| Input voltage | 100 – 250 VAC |
| Output | max 25 W, ± 5 VDC |
| Control range | 5 – 80 °C |
| Setpoint resolution | 0.01 °C |
| Absolute accuracy | ± 0.1 °C |
| Stability over 24 h | ± 0.01 °C |
| Ambient to 70 °C | 4 minutes |
| 70 °C to 30 °C | 4 minutes |
| Dimensions (L × W × H) | 199 × 158 × 74 mm |
Information we need
The more of this you can give us up front, the faster we can turn a quotation around.
- Crystal dimensionsLength and aperture, so the mount and clamp are sized to fit.
- Target setpointThe operating temperature your phase‑matching depends on.
- Stability requirementHow tight a tolerance your experiment needs the setpoint held to.
- MountingOur standard mount or a custom bracket — tell us how it needs to fit your setup.
- Quantity & timelineHow many units, and when you need them by.
Ovens and crystals
Tell us the crystal and we size the mount and the setpoint around it.
PPKTP phase‑matching calculator
Poling period, output wavelengths, temperature tuning and acceptance bandwidths for SPDC, SHG, SFG and DFG in PPKTP — calculated live with the same in‑house model our engineers use.
Output
Request a quotation
Request a quotation
Tell us what you need and we'll come back with pricing, lead time and, where relevant, a custom poling design.
About SLF Quantum
SLF Quantum designs and manufactures nonlinear optical components for quantum optics and photonics research, from our facility in Stockholm, Sweden — part of Svenska Laserfabriken AB.
Our range covers the whole chain: PPKTP crystals and waveguides to generate and convert light, the SPUD to detect single photons at 1550 nm, and ovens to hold each crystal at its phase‑matching temperature. Every PPKTP crystal is tested individually and ships with its own test report, so you know exactly how it performs before it goes into your setup.
Stock crystals ship quickly from Stockholm. For custom crystals we work back from your experiment: your wavelengths, bandwidth, temperature setpoint and polarization define the poling design, for a single crystal or a complete photon source.
Individually tested components, not statistical batches.
Worldwide shipping to labs on six continents.
Custom engineering built around your experiment, not our catalog.
30+ countries, six continents — every crystal shipped, tracked and tested.
Our team
Every team member holds a relevant technical education — a shared foundation for quality, accuracy and reliability at every stage.
Get in touch
For quotations, use the quotation page — for everything else, reach us directly or send a note below.
Ruddammsvägen 49, one floor down
114 19 Stockholm, Sweden
Spannmålsvägen, 762 51 Rimbo, Sweden
Chengdu Dien Photoelectric Technology Co., Ltd.
Longquanyi District, Chengdu, P.R. China
Privacy policy
How SLF Svenska Laserfabriken AB handles personal data — what we collect, why, who sees it, and how long we keep it.
Last updated: 28 October 2026
Who we are
SLF Svenska Laserfabriken AB (org. no. 559119‑4559) is responsible for the personal data described in this policy. We make nonlinear optical crystals, waveguides and photon‑detection products, and sell them mainly to universities, research institutes and companies.
This policy covers our websites slfcrystals.com, slfquantum.com and laserfabriken.com, and our contact with customers, suppliers and others we do business with.
Address: SLF Svenska Laserfabriken AB, Ruddammsvägen 49, 114 19 Stockholm, Sweden
Email: info@laserfabriken.com
Phone: +46 70 761 61 51
What personal data we collect
We collect business contact details and the information needed to handle enquiries and orders. We do not collect sensitive personal data, and we do not buy contact lists.
- Website enquiries: name, email address, organisation and the content of your message, when you use a contact form.
- Customers and suppliers: name, job title, work email, phone number, organisation, delivery and billing address, and VAT number.
- Orders and quotes: what you asked for or bought, quotes, order confirmations, invoices and shipping details, including end‑user information where export rules require it.
- Payments: payment references and bank details for invoices. Card payments through PayPal are handled by PayPal; we do not see or store card numbers.
- Correspondence: emails and other messages you send us.
Why we use it and our legal basis
We only use personal data to run our business with you. We do not send marketing emails or newsletters, we do not sell personal data, and we do not use automated decision‑making or profiling.
| Answering enquiries from our websites, email or phone | Legitimate interest in responding to people who contact us |
| Preparing quotes, handling orders, delivering products and providing support | Performance of a contract, or steps before entering one |
| Invoicing, bookkeeping and accounting | Legal obligation (Swedish Bookkeeping Act) |
| Export control, customs and sanctions checks | Legal obligation |
| Keeping track of our customer and supplier relationships | Legitimate interest in running and developing our business |
| Handling legal claims | Legitimate interest in establishing, exercising or defending legal claims |
Who we share it with
We share personal data only when it is needed for the purposes above.
- Service providers that process data for us: email and file storage (Microsoft), accounting and invoicing (SpeedLedger), and website hosting (one.com and Wix). They may only use the data on our instructions.
- Banks and payment providers: our bank and PayPal, to receive payments.
- Couriers and freight forwarders: to deliver your order.
- Auditors and legal advisers: when they need it for their work for us.
- Authorities: for example the Swedish Tax Agency, customs or export control authorities, when the law requires it.
- A new owner: if all or part of our business is sold or merged, personal data may be transferred to the new owner, who will continue to protect it as described here.
Transfers outside the EU/EEA
We store data mainly within the EU/EEA, but some of our service providers may process it in other countries, for example the United States.
When that happens, the transfer is protected by an EU adequacy decision (such as the EU–US Data Privacy Framework) or by the European Commission's standard contractual clauses. When you are a customer outside the EU/EEA, we send order and shipping details to your country because that is needed to deliver to you.
How long we keep it
We keep personal data only as long as we need it, then delete it.
| Website enquiries that do not lead to business | Up to 2 years after our last contact |
| Customer and supplier contact details | As long as we do business, then up to 3 years after our last order or contact |
| Invoices and accounting records | 7 years after the end of the calendar year they relate to, as the Swedish Bookkeeping Act requires |
| Export control records | As long as export control rules require |
How we protect it
We protect personal data with technical and organisational measures suited to a small company. Our systems use two‑factor login, our computers are encrypted and receive automatic security updates, and only staff who need the data for their work can access it.
Your rights
You can contact us at info@laserfabriken.com to use any of your rights under the GDPR. We will reply within one month.
- Access: get a copy of the personal data we hold about you.
- Correction: have incorrect data corrected.
- Deletion: have your data deleted, unless we must keep it by law, for example invoices.
- Restriction: ask us to limit how we use your data.
- Objection: object to our use of your data based on legitimate interest.
- Data portability: receive data you gave us in a machine‑readable format.
If you are unhappy with how we handle your data, you can complain to the Swedish Authority for Privacy Protection (IMY), www.imy.se, or to the data protection authority where you live.
Cookies
Our websites use only the cookies needed for the site and its contact forms to work. We do not use cookies for advertising or to track you across other websites.
Changes and contact
We may update this policy when our business or the rules change; the date at the top shows the latest version. Questions about this policy or your personal data are welcome at info@laserfabriken.com.